mansonry-glue – NCL AAC Blocks

PRODUCT DESCRIPTION

NCL Self Cured Masonry Glue 110 is factory premixed and formulated to apply with water to construct high strength thinnest mortar to lay AAC Bricks, Fly Ash / Concrete Blocks. It is a blend of inorganic fillers, cement, additives and polymers. Masonry Glue 110 replaces conventional mortar of 12 -18 mm thickness with 3-4 mm.

ADVANTAGES

Factory premixed which saves labour & time
Speedy work
Curing is not required which saves water & labour
High strength product
Good flexural strength
Good splitting tensile strength
Good open time
Cost effective
No VOC

APPLICATION AREAS

Suitable for interior & exterior applications
To lay AAC Bricks, Fly Ash / Concrete Blocks
To fix cement door & window frames
For boundary walls

PACKING SIZES

40 Kg., and 50 Kg.

3.20 sft/ kg or 0.297 m2 with 6mm thick bed on 4" AAC Blocks
1.28 sft / kg or 0.119 m2 / kg with 6mm thick bed on 9" AAC Blocks

TECHNICAL DATA

Sl. No.	Attributes	Test	Results
1	Colour	Mfg. Spec	Grey
2	Water Mixing Proportion	Mfg. Spec	16 % to 20%
3	Pot Life	Mfg. Spec	60 minutes
4	Open Time	Mfg. Spec	20 minutes
5	Ready for Plastering	Mfg. Spec	24 hours
6	Compressive Strength	ASTM	> 4.5 Mpa
7	Flexural Strength	ASTM	> 4 Mpa
8	Splitting Tensile Strength	ASTM	>300 Kpa

SURFACE PREPARATION

Ensure that the surface should be free from dust, oil, grease, paints, loose foreign particles /materials and curing agents which may affect adhesion
Wet the surface before application without leaving excess water

MIXING

Add 165 ml of clean water into a bucket and gradually transfer 1 kg of NCL Masonry Glue 110 in it. Mixing can be done manually or slow speed electrical mixer. The mixing is to be done till it forms a lump free homogenous mix and to attain the water percentage 16 to 20%. If required, add extra water to obtain uniform paste. Leave the dough for 5 minutes for polymerization. Do not keep the dough under direct sunlight.

APPLICATION

Apply a thin layer of the above dough by using notching trowel in the thickness of 3 to 4 mm (or client requirement) on the clean and levelled surface on which the block work is to be carried out, fix the block on the laid glue in a proper line and level. On the first block apply the glue of the same 3-4mm thickness on both horizontal and vertical joint of the block and continue laying the brick with 3-4mm thickness of glue and keep a check in the wall levels.

SHELF LIFE

12 months

STORAGE

Store in a moisture-free dry place

PRECAUTIONS

Keep out of reach of children
Keep in a dry place
Avoid inhalation of dust
If it comes in contact with eyes or you feel skin irritation, wash with plenty of plain water and consult a doctor

DO'S

The level from base to the top layer should be properly horizontal
There should not be any gap between the joints of AAC Blocks
Bottom layer of AAC Block should be properly laid, so that no gaps should come in between otherwise the blocks would crack
The lentil should be placed after every 5 to 6 layers of AAC Blocks or 6 m length to avoid cracks. It should be placed on a complete block
Storage on dry and even surface to avoid damage and contact with moisture
Before application – wet the block
Use self curing block mortar with 3 to 4 mm thickness only and notching is mandatory
Use a tool like hacksaw or rotary cutter
Should rest on full block

DON'TS

Do not use a rich mortar mix as it tends to shrink & might crack
Do not flood the brick with water
Do not construct a wall without coping the beam
Do not stack the blocks in haphazard manner or leave them exposed to rain or moisture
Do not use tools like hammer, chisel etc. to cut the block

Marketed by:
NCL Buildtek Ltd.,
10-3-162, 5th Floor, NCL Pearl,
SD Road, East Maredpally,
Secunderabad - 500 026.
Ph: +91 40 6831 3333
e-mail: contactus@nclbuildtek.com
Website: www.nclbuildtek.com

Download Mansonry Glue 110 Self Curing

Download Mansonry Glue 110 Normal

NCL MASONRY GLUE 110 (self-curing)