RENDER 608 HP (self-curing)

prod Image
PRODUCT DESCRIPTION

NCL Render 608 HP is a factory ready-mixed plaster and made of inorganic fillers, cement, additives and polymers. It is suitable to apply on fly ash bricks, clay bricks, AAC Blocks, concrete blocks etc.to achieve the required thickness.

prod Image
ADVANTAGES
  • Factory premixed which saves labour & time
  • Speedy work
  • High compressive strength
  • Good tensile strength
  • Good flexural strength
  • Minimizes shrinkage
  • Minimizes hair line cracks
  • Cost effective
  • No VOC
prod Image
APPLICATION AREAS
  • Suitable for interior & exterior applications
  • Suitable to apply on fly ash bricks, clay bricks, AAC Blocks, concrete blocks
  • Any other cementitious substrates
  • For filling the cavity, holes and irregularities to level the surface
prod Image
PACKING SIZES
40 Kg., 5 Kg. and 1Kg
prod Image
COVERAGE
0.53 sft/ kg or 0.049 m2 per kg at an average thickness of 10 mm
prod Image
TECHNICAL DATA
Sl. No. Attributes Standard Results
1 Colour Mfg. Spec Grey
2 Water Mixing Proportion Mfg. Spec 17.5 % to 20%
3 Pot Life Mfg. Spec 60 minutes
4 Compressive ASTM > 4 Mpa
5 Flexural Strength ASTM > 2 Mpa
6 Tensile Strength ASTM > 0.5 Mpa
prod Image
SURFACE PREPARATION
  • Ensure that the wall's surface should be free from dust, oil, grease, paints, loose foreign particles/materials and curing agents which may affect adhesion
  • Proper hacking to be done on concrete
  • Wet the surface before application without leaving excess water
  • Before application proper wall plumbing measures are to be taken
prod Image
MIXING
Add 175 ml of clean water into a tub and gradually transfer 1 kg of NCL Render 608 HP in it. Mixing can be done manually or with slow speed electrical mixer. The mixing to be done till it forms a lumpfree homogenous mix and to attain water percentage of 17.5 % to 20%. If required add extra water to obtain uniform paste. Leave the dough for 5 minutes for polymerization. Do not keep the dough under direct sunlight.
prod Image
APPLICATION
  • Apply the dough with help of steel trowel on the bare brick wall surface from base of the surface to upward to get an average thickness of 10 mm. If required apply more material to achieve 10 mm thickness
  • Coat on coat can be done up to 18 mm thickness
  • To make the surface smooth & uniform run the wooden / fibre / plastic trowel
  • For immediate strength & better performance 1 to 2 days curing is required based on weather conditions
prod Image
SHELF LIFE
12 months
prod Image
STORAGE
Store in a moisture-free dry place
prod Image
PRECAUTIONS
  • Keep out of reach of children
  • Keep in a dry place
  • Avoid inhalation of dust
  • If it comes in contact with eyes or you feel skin irritation, wash with plenty of plain water and consult a doctor
DO'S
  1. The level from base to the top layer should be properly horizontal
  2. There should not be any gap between the joints of AAC Blocks
  3. Bottom layer of AAC Block should be properly laid, so that no gaps should come in between otherwise the blocks would crack
  4. The lentil should be placed after every 5 to 6 layers of AAC Blocks or 6 m length to avoid cracks. It should be placed on a complete block
  5. Storage on dry and even surface to avoid damage and contact with moisture
  6. Before application – wet the block
  7. Use self curing block mortar with 3 to 4 mm thickness only and notching is mandatory
  8. Use a tool like hacksaw or rotary cutter
  9. Should rest on full block
DON'TS
  1. Do not use a rich mortar mix as it tends to shrink & might crack
  2. Do not flood the brick with water
  3. Do not construct a wall without coping the beam
  4. Do not stack the blocks in haphazard manner or leave them exposed to rain or moisture
  5. Do not use tools like hammer, chisel etc. to cut the block
Marketed by:
NCL Buildtek Ltd.,
10-3-162, 5th Floor, NCL Pearl,
SD Road, East Maredpally,
Secunderabad - 500 026.
Ph: +91 40 6831 3333
e-mail: contactus@nclbuildtek.com
Website: www.nclbuildtek.com
Preloader image